Dripping tap: repair it or replace it?
A dripping tap does not automatically need replacing. A repair may be worth considering if the tap body is sound, the model can be identified and a suitable replacement part is available. Replacement becomes more useful to discuss when the body is damaged, compatible parts cannot be found or previous repairs have not resolved the cause.
By Plumber Leicester Pro editorial team · Sources checked . General guidance; repairs depend on your fittings and property.
In this guide
First establish where the water is escaping. A drip from the spout, water around the handle and a wet cupboard underneath can involve different faults. If water is spreading outside the sink or basin, deal with the active leak before comparing replacement designs.
Where is the water coming from?

| What you notice | What to report |
|---|---|
| A continuing drip from the spout after the tap is closed | Note whether it continues after the fitting has settled and whether one or both controls are involved. |
| Water around the handle or where a swivelling spout meets the body | Describe the exact point where water first appears. Do not assume the same part causes every leak. |
| Water around the base or beneath the sink | Report whether it appears during use or continues afterwards. Connections or another fitting may need checking. |
| A few drops immediately after turning the tap off, then it stops | Check the model's instructions. Residual water can drain from a spout; this differs from a continuing leak. |
Do not keep operating a tap to reproduce a leak that is already wetting a cupboard or floor. Our leaking-tap enquiry page explains how to arrange a local assessment.
Why can a closed tap still drip?
Inside the fitting, a valve or cartridge controls the water. Wear, debris or damage can prevent it from closing as intended. Some taps use replaceable washers; others use ceramic-disc mechanisms or manufacturer-specific cartridges. There is no single washer or cartridge that fits every tap.
Bristan's customer guidance describes how limescale or water-borne debris can affect its valves, and directs owners to the fitting instructions for their particular product. It also distinguishes brief spout drainage from a continuing drip. That guidance is a useful example of why the make and model matter; it does not diagnose every brand or recommend one repair for all taps.
Avoid repeatedly tightening the handle harder to make the drip stop. Note the symptoms and arrange the appropriate check instead. Do not dismantle unfamiliar controls or assume a cleaning method for one manufacturer's cartridge is safe for another fitting or finish.
When is a repair worth considering?
A repair is a reasonable option to discuss when the rest of the fitting remains suitable for the home and the faulty part can be identified. Ask the person assessing it to explain:
- Which part appears to be at fault, and what supports that diagnosis.
- Whether an exact or manufacturer-approved compatible part is available.
- Whether the tap body, seating and connections are sound enough for that repair.
- Whether the proposed repair includes checking that the leak has stopped.
Replacing a serviceable component can retain a fitting that otherwise works well. However, a part price found online is not the whole repair price: access, diagnosis, labour and another visit may also matter.
Look for the original receipt, installation paperwork, product box or a readily visible model marking. Bristan has a product and spares finder; other manufacturers have their own support routes. A photograph of the outside may help narrow the search, but a similar-looking tap is not proof that its internal parts match.
When should you discuss replacing the tap?
Ask about replacement if there is damage to the body or the proposed repair cannot provide a dependable result. Scarce parts, difficult access or a repeated unresolved problem can also change the comparison. Do not use age alone as a rule that a tap must be replaced.
Compare the complete options, including any access work and the suitability of the new fitting. A replacement needs to suit the sink or basin, mounting arrangement and water supply. An attractive product photograph does not establish those things.
Tell the supplier if you need easier controls, different reach over the basin or another practical improvement. Those needs can make replacement more worthwhile, but they should be assessed alongside the plumbing requirements. If you are thinking of fitting a specialist boiling-water or filtered-water system, describe that separately; it is not the same job as replacing an ordinary mixer tap.
Compare the two quotes on the same basis
Ask for a repair option and a replacement option where both are practical. For each, establish what is included:
- The visit or diagnostic charge, labour and any minimum charge.
- The named part or replacement tap, who supplies it and whether it is included.
- Access, connection work and removal of the old fitting where needed.
- Any further visit, out-of-hours charge, VAT and how extra work is authorised.
- The checks at completion, who invoices you and the applicable parts/work terms.
Check the current manufacturer's guarantee before buying parts or authorising work if the fitting may still be covered. Eligibility and exclusions depend on the product and its terms. A product guarantee and the terms for installation work are separate matters; ask who handles each.
There is no reliable universal point at which a repair becomes “too expensive”. Compare the actual diagnosis and complete written options for your fitting, rather than an assumed local average or an unrelated online parts price.
What can you do while waiting?
If it is a continuing spout drip into an otherwise freely draining basin, keep that basin clear and report the fault. WaterSafe's household plumbing guidance includes dripping taps among the leaks worth addressing. Do not assume a small drip will cost a particular amount; water lost and any bill impact depend on the leak and your billing arrangement.
For an active escape outside the basin, close a clearly identified, safely accessible valve serving the affected fitting only if you know how. Do not force a seized valve or experiment with unknown controls. If you cannot safely stop the escape, discuss urgent help. Keep clear of any water near sockets or electrical appliances.
If you rent, report the fault to the landlord or managing agent and follow their repair process. Agree authority and payment before booking private work. Leicester City Council tenants can use the council's repair-reporting service.
Need help choosing a tap repair in Leicester?
Call 0116 488 6858 or send a plumbing enquiry. Have your postcode, the leak location, any model information and details of previous repairs ready. Say if water is escaping now so urgent availability can be discussed.
Plumber Leicester Pro handles enquiries 24/7. The supplier assesses the fitting and confirms coverage, attendance, the proposed work and charges before you agree to a booking.
